17-4PH vs 15-5PH: differences and when to use
15-5PH (UNS S15500) is a version of 17-4PH (S17400) with less chromium and almost no delta ferrite. Both are precipitation hardened with the same treatments (H900 to H1150) and reach similar strength, but 15-5PH has better transverse toughness and ductility in large sections, which is why it is preferred in aerospace. For shafts, valves and general parts, 17-4PH does the job and is easier to find.
| Property | 17-4PH stainless steel – UNS S17400 (ASTM A564 Type 630) | 15-5PH – UNS S15500 (XM-12) |
|---|---|---|
| Identification | ||
| Group | Stainless steels | Stainless steels |
| UNS | S17400 | S15500 |
| W.Nr. / EN | 1.4542 (X5CrNiCuNb16-4) | 1.4545 (X5CrNiCu15-5) |
| Chemical composition (%) | ||
| C | ≤ 0.07 | ≤ 0.07 |
| Mn | ≤ 1.00 | ≤ 1.00 |
| Si | ≤ 1.00 | ≤ 1.00 |
| P | ≤ 0.040 | ≤ 0.040 |
| S | ≤ 0.030 | ≤ 0.030 |
| Cr | 15.0 – 17.5 | 14.0 – 15.5 |
| Ni | 3.0 – 5.0 | 3.5 – 5.5 |
| Cu | 3.0 – 5.0 | 2.5 – 4.5 |
| Fe | balance | balance |
| Nb | 0.15 – 0.45 (Nb+Ta) | 0.15 – 0.45 (Nb+Ta) |
| Composition: standard | ASTM A564 Type 630 | ASTM A564 XM-12 |
| Mechanical properties (minimum) | ||
| Yield strength | – | – |
| Tensile strength | – | – |
| Elongation | – | – |
| Hardness | – | – |
| Properties: condition | Aged – ASTM A564 minimums (bar); see the aging table | Aged – ASTM A564 minimums (bar, longitudinal); other conditions in the aging table |
| Use and supply | ||
| PREN (minimum – typical) | 15 – 16 | 14 – 15 |
| Density | – | – |
| Service temperature | Up to ≈ 315 °C; above that, prolonged exposure embrittles (loss of toughness). | Up to ≈ 315 °C; prolonged exposure above that causes embrittlement (475 °C aging). |
| Standards by product form | Bar: ASTM A564 Type 630; AMS 5643; AMS 5622 (VAR) Forging: ASTM A705 Type 630; AMS 5643 Plate: ASTM A693 Type 630; AMS 5604 Casting: ASTM A747 CB7Cu-1 H2S service: NACE MR0175/ISO 15156 (H1150D, ≤ 33 HRC) | Bar: ASTM A564 XM-12; AMS 5659 Forging: ASTM A705 XM-12; AMS 5659 Plate: ASTM A693 XM-12; AMS 5862 Equivalent casting: ASTM A747 CB7Cu-2 |
| Typical applications | Pump and propeller shafts Valve stems and internals Aircraft hardware and fittings Studs, bolts and couplings | Aircraft structures and fittings Shafts and valve stems Pump and compressor components Gears and couplings |
Composition and minimum properties per the standard listed on each datasheet; PREN uses the minimum and the middle of the ranges. For the actual value, use the heat certificate.
Most searched comparisons
- 316 / 316L stainless x 317L stainless steel
- Duplex 2205 (F51 / S31803) x Super duplex 2507 / F53 / S32750
- Duplex 2205 (F51 / S31803) x Duplex S32205 / F60
- Inconel 625 / Alloy 625 x Incoloy 825
- SAE 4140 x SAE 4340
For pitting resistance, see the PREN calculator; for steel weldability, the carbon equivalent; to choose by medium, steel by corrosive medium.
Frequently asked questions
Is the heat treatment the same?
Yes. Both are solution annealed (condition A) and aged at the same temperatures; the H condition sets strength and hardness.
Which one has better corrosion resistance?
They are similar, around that of a 304. Neither is suited to stagnant seawater.
Can I replace 17-4PH with 15-5PH?
Generally yes, in the same H condition. Check the drawing: aerospace and some customers require the specific standard (for example AMS 5659 for 15-5PH).